+echo "$ac_t""$lt_cv_cc_needs_belf" 1>&6
+ if test x"$lt_cv_cc_needs_belf" != x"yes"; then
+ # this is probably gcc 2.8.0, egcs 1.0 or newer; no need for -belf
+ CFLAGS="$SAVE_CFLAGS"
+ fi
+ ;;
+
+
+esac
+
+
+# Save cache, so that ltconfig can load it
+cat > confcache <<\EOF
+# This file is a shell script that caches the results of configure
+# tests run on this system so they can be shared between configure
+# scripts and configure runs. It is not useful on other systems.
+# If it contains results you don't want to keep, you may remove or edit it.
+#
+# By default, configure uses ./config.cache as the cache file,
+# creating it if it does not exist already. You can give configure
+# the --cache-file=FILE option to use a different cache file; that is
+# what configure does when it calls configure scripts in
+# subdirectories, so they share the cache.
+# Giving --cache-file=/dev/null disables caching, for debugging configure.
+# config.status only pays attention to the cache file if you give it the
+# --recheck option to rerun configure.
+#
+EOF
+# The following way of writing the cache mishandles newlines in values,
+# but we know of no workaround that is simple, portable, and efficient.
+# So, don't put newlines in cache variables' values.
+# Ultrix sh set writes to stderr and can't be redirected directly,
+# and sets the high bit in the cache file unless we assign to the vars.
+(set) 2>&1 |
+ case `(ac_space=' '; set | grep ac_space) 2>&1` in
+ *ac_space=\ *)
+ # `set' does not quote correctly, so add quotes (double-quote substitution
+ # turns \\\\ into \\, and sed turns \\ into \).
+ sed -n \
+ -e "s/'/'\\\\''/g" \
+ -e "s/^\\([a-zA-Z0-9_]*_cv_[a-zA-Z0-9_]*\\)=\\(.*\\)/\\1=\${\\1='\\2'}/p"
+ ;;
+ *)
+ # `set' quotes correctly as required by POSIX, so do not add quotes.
+ sed -n -e 's/^\([a-zA-Z0-9_]*_cv_[a-zA-Z0-9_]*\)=\(.*\)/\1=${\1=\2}/p'
+ ;;
+ esac >> confcache
+if cmp -s $cache_file confcache; then
+ :
+else
+ if test -w $cache_file; then
+ echo "updating cache $cache_file"
+ cat confcache > $cache_file
+ else
+ echo "not updating unwritable cache $cache_file"
+ fi
+fi
+rm -f confcache
+
+
+# Actually configure libtool. ac_aux_dir is where install-sh is found.
+CC="$CC" CFLAGS="$CFLAGS" CPPFLAGS="$CPPFLAGS" \
+LD="$LD" LDFLAGS="$LDFLAGS" LIBS="$LIBS" \
+LN_S="$LN_S" NM="$NM" RANLIB="$RANLIB" \
+DLLTOOL="$DLLTOOL" AS="$AS" OBJDUMP="$OBJDUMP" \
+${CONFIG_SHELL-/bin/sh} $ac_aux_dir/ltconfig --no-reexec \
+$libtool_flags --no-verify $ac_aux_dir/ltmain.sh $host \
+|| { echo "configure: error: libtool configure failed" 1>&2; exit 1; }
+
+# Reload cache, that may have been modified by ltconfig
+if test -r "$cache_file"; then
+ echo "loading cache $cache_file"
+ . $cache_file
+else
+ echo "creating cache $cache_file"
+ > $cache_file
+fi
+
+
+# This can be used to rebuild libtool when needed
+LIBTOOL_DEPS="$ac_aux_dir/ltconfig $ac_aux_dir/ltmain.sh"
+
+# Always use our own libtool.
+LIBTOOL='$(SHELL) $(top_builddir)/libtool'
+
+# Redirect the config.log output again, so that the ltconfig log is not
+# clobbered by the next message.
+exec 5>>./config.log
+
+
+
+
+# Check whether --enable-comp or --disable-comp was given.
+if test "${enable_comp+set}" = set; then
+ enableval="$enable_comp"
+ :
+else
+ enable_comp=yes
+fi
+
+if test "$enable_comp" = "yes"; then